Guides / Intrepid I-0 Manual

Intrepid I-0 Manual

How to set up, shoot with and look after your Intrepid I-O shutter system, with the latest firmware and help for every message on the screen.

Updated 19 November 2026

What's in the Box

controllerI-O ShutterUSB-C cablelanyard
  • The Controller — the handheld unit with the screen and four buttons.
  • The I-O Shutter, with its retaining ring already attached.
  • A USB-C cable — connects the Controller to the I-O Shutter, and is also used for charging and firmware updates.
  • A lanyard — attaches to the hole in the top-left corner of the Controller's faceplate. Handy for hanging the Controller off a tripod or the camera itself.
  • A card with:
    • A QR code linking to this documentation.
    • The serial numbers for your Controller and I-O Shutter.
    • A quick start guide.
    • A link to the warranty information online.

What You'll Also Need

Not included in the box — you'll need your own:

  • A lens board, sized for your camera and format (4x5/5x7/8x10), for the I-O Shutter to mount to.
  • A Copal 0-compatible lens.

See Getting started for how these fit together with the I-O Shutter.

Getting Started

The Controller's Ports

charge port · CHRUSB-C, 500mA+ chargerflash port3.5mm jackshutter port · SHUI-O Shutter + firmware
CHR and SHU look the same. Check the label before plugging in.

Looking at the front of the Controller, there are three ports, right to left:

Port Label What it's for
3.5mm jack — Connecting a flash
USB-C SHU Connecting the I-O Shutter, and updating firmware
USB-C CHR Charging the Controller's battery

Caution: CHR and SHU look identical but do different jobs, so check the label before plugging in. Charging the Controller from the SHU port, or trying to run the I-O Shutter from CHR, won't work.

Charging

Plug a USB-C cable into the CHR port to charge the Controller. You can use the I-O Shutter's supplied cable, or any standard USB-C cable/charger. We recommend a charger with an output of 500mA or more; a weaker charger may charge very slowly, especially if you keep using the system while it charges.

  • A small battery icon in the bottom-right of the screen shows charge level and charging status.
  • You can keep using the system while it charges.
  • A full charge from a low battery takes approximately 1 hour 50 minutes.

Mounting and Connecting the I-O Shutter

Caution: Mounting order matters. The I-O Shutter has to go onto the lens board before the lens is attached. If you attach the lens to the I-O Shutter first, the lens's rear element is too large to then pass through the lens board's hole, and you won't be able to fit the retaining ring.

  1. Mount the I-O Shutter onto your lens board using the retaining ring.
  2. Attach your Copal 0-compatible lens to the front and rear of the I-O Shutter.
  3. Mount the assembled lens board onto your camera's front standard, the same way you'd mount any other lens board.
  4. Connect the supplied USB-C cable between the I-O Shutter and the Controller's SHU port.
123
I-O Shutter onto the BoardThrough the lens board hole, held by the retaining ring from behind.Then the LensFront cell into the front, rear cell into the back.Board onto the CameraLike any other lens board, then connect the cable to SHU.

Lanyard Attachment Point

There's a hole in the top-left corner of the Controller's faceplate for attaching the included lanyard — useful for hanging the Controller off a tripod or the camera itself while you're shooting.
Avoid letting it hang only from the I-O Shutter's cable.

Turning the System on

Use the power switch on the front of the Controller, to the left of the RELEASE button. It also brings the connected I-O Shutter to life; there's no separate switch on the I-O Shutter itself. On power-up you'll see the Intrepid splash screen, then the main screen. If the Shutter is connected the screen briefly shows a "Shutter connected" message. If the two units ever lose their connection the Controller will let you know on screen — see Troubleshooting.

Turning the System Off

Switch the power off the same way. If you switch off while an exposure is still running, the Controller waits until that exposure finishes (or is cancelled) before actually powering down, so a shot in progress is never cut short.

The Controls

Short press for main function, long press for secondary function.

lanyard pointreleasepowerenterupdowncharge portUSBC, 500mA+shutter portUSBCflash port3.5mm jack

Tap a label, a button, a port or the screen.

Controls in the Main Screen

Button Short press Long press (press and hold)
UP Move the highlight up / increase a value From the main screen: open the Settings menu
DOWN Move the highlight down / decrease a value From the main screen: open the Settings menu
ENTER Select the highlighted item / confirm a value Manually open or close the shutter/aperture (see The main screen)
RELEASE Take the photo, or start/cancel the self-timer Cancel an exposure that's currently running

Controls in the Settings Menus

The buttons work the same way on every settings page and sub-page:

Button Short press Long press (press and hold)
UP Move the highlight up / step a value up Go back one level (sub-page → Settings → main screen)
DOWN Move the highlight down / step a value down Go back one level (sub-page → Settings → main screen)
ENTER Edit the highlighted setting / confirm a new value Nothing
RELEASE Still takes a photo, as normal Still cancels a running exposure

The Main Screen

The main screen, showing 100, f8.0, Arm and EV11.5123456789
  1. 1Selection bar: the row you're on
  2. 2Shutter speed, or the LONG time, BULB or TIME
  3. 3Shutter open or closed
  4. 4Aperture
  5. 5Aperture open or closed
  6. 6Arm or READY
  7. 7Exposure value
  8. 8Self-timer
  9. 9Battery and charging
Point at an item to find it on the screen.

The main screen is where you'll spend most of your time. It has three rows, and a white bar on the left shows which one is currently highlighted:

  1. Shutter speed (top) — or, depending on your exposure mode, a hh:mm:ss duration you set yourself (LONG), or the word BULB or TIME. See Taking a photo.
  2. Aperture (middle) — shown as an f-number, e.g. f8.0.
  3. Arm / Ready (bottom left) — shows Arm when the shutter and/or aperture are open, and READY once both are closed and the system is ready to fire.

Around the edges of the screen:

  • Shutter and aperture icons (top right) — each shows a closed symbol when that part is closed, and an open circle when it's open, so you can see the shutter and aperture's physical state at a glance.
  • Self-timer icon — shown with a number when the self-timer is set to fire after a delay; a blank timer icon when it's off.
  • Exposure value (EV) — a live readout calculated from your current shutter speed, aperture and ISO, shown as EV followed by a number.
  • Battery icon (bottom right corner) — charge level, or a charging indication while plugged in.

Moving Around and Editing a Value

Editing the aperture.
Editing the aperture.
  • Press UP/DOWN to move the highlight between the three rows.
  • Press ENTER on the shutter speed or aperture row to open it for editing, then UP/DOWN to change the value, then ENTER again to confirm and close it. In BULB and TIME modes there is nothing to edit on the top row, so ENTER does nothing there.

Manually Opening and Closing the Shutter or Aperture

Sometimes you want to open the shutter or aperture — for example to compose and focus on the ground glass.
Highlight the shutter speed or aperture row then press and hold ENTER:

  • On the shutter speed row: toggles the shutter open/closed.
  • On the aperture row: toggles the aperture open/closed.
  • On the Arm row: toggles both together.

Taking a Photo

1. Set Your Shutter Speed and Aperture

On the main screen, highlight the shutter speed row and press ENTER, then UP/DOWN to choose a speed, then ENTER to confirm. Do the same on the aperture row.

  • Shutter speeds range from 1/125 down to 30s.
  • Aperture range available depends on your lens — see Setting up a lens.
  • The EV readout in the middle of the screen updates live as you change either value, calculated together with your current ISO setting.

2. READY the Shutter

READY: shutter and aperture closed, ready to fire.
READY: shutter and aperture closed, ready to fire.

The bottom-left of the screen shows either Arm or READY:

  • Arm — the shutter and/or aperture are currently open. Highlight this row and press ENTER to close both and set the system READY (you can press and hold ENTER on this row to open/close both at once).
  • READY — the shutter and aperture are both closed and the shutter is armed, the shutter will fire when you press RELEASE.

See Safe Shot in the setting if you wish to remove the extra Arm step before every shot Settings menu.

3. Press RELEASE

Press the RELEASE button to take the photo. If the system isn't ready, it'll give a warning beep instead of firing.
If Safe Shot is on (default: on) then you will need to Arm again in order to shoot again.

Cancelling a Shot in Progress

For slow shutter speeds and long exposures, the shutter stays open for a while after you press RELEASE, and the screen shows an "Exposure in progress" message. To cancel it before it finishes, press and hold RELEASE. (BULB and TIME exposures are ended differently — see below.)

Using the Self-timer

Self-timer set to 10 seconds.
Self-timer set to 10 seconds.
  1. In the Settings menu, set SELF TIMER to a delay: 2, 4, 10, 30 or 60 seconds (or OFF).
  2. Back on the main screen, a timer icon with your chosen delay appears next to the aperture.
  3. Press RELEASE as normal — instead of firing immediately, the screen counts down, beeping as it goes, then fires automatically at zero.
  4. To cancel a countdown in progress, press RELEASE again before it reaches zero.

Exposure Modes

Set EXPOSURE MODE in the Settings menu to choose how the shutter is timed: NORMAL, LONG, BULB or TIME. Arming, safe shot and the flash sync settings work the same way in every mode.

Normal

The shutter fires for the shutter speed shown on the top row, as described above.

Long Exposure

LONG exposure mode: the top row shows hours, minutes and seconds.
LONG exposure mode: the top row shows hours, minutes and seconds.
Setting the long exposure time.
Setting the long exposure time.

For exposures longer than the 30-second maximum on the normal shutter speed dial. The top row of the main screen changes from a shutter speed to an hours:minutes:seconds duration you set yourself:

  1. Highlight the top row and press ENTER to open the editor.
  2. UP/DOWN rolls the highlighted field (hours, minutes or seconds).
  3. Press and hold UP/DOWN to move between fields.
  4. Press ENTER to confirm.

The EV readout isn't meaningful in this mode (shown as EV n/a), since it's designed for exposures too long for a normal light-meter calculation to be useful. Firing and cancelling work exactly the same as a normal shot.

Bulb

The shutter stays open for as long as you hold the RELEASE button.

While the shutter is open, the screen shows a timer counting up from 00:00:00.

The shortest exposure in this mode is about 0.15s.

Time

The shutter opens when you press RELEASE and stays open until you press RELEASE again.

While the shutter is open, the screen shows a timer counting up from 00:00:00.

The shortest exposure in this mode is about 0.15s.

In BULB and TIME modes the EV readout shows EV n/a. First-curtain flash sync works as normal; second-curtain flash doesn't fire, because the closing time isn't known in advance. See Using a flash.

Using a Flash

Connect your flash to the Controller's 3.5mm flash sync jack (see Getting started and the flash trigger voltage notes in Care and specifications). Then switch on 1ST CURTAIN, 2ND CURTAIN or both in the Flash Sync menu:

  • 1ST CURTAIN fires the flash just as the shutter opens.
  • 2ND CURTAIN fires the flash just before the shutter closes.

You can switch on both curtains to fire the flash twice. Many flashes can't recover quickly enough to fire twice at fast shutter speeds, where the two pulses are only a few milliseconds apart, and will most likely only fire on the first curtain in that case.

Flash sync works with every exposure mode. In BULB and TIME modes only the first curtain fires, because the closing time isn't known in advance.

The Settings Menu

The buttons work the same way on every settings page. See The controls for what each button does.

Settings, first page.
Settings, first page.
Settings, scrolled down.
Settings, scrolled down.
Settings, further down.
Settings, further down.

Press and hold UP or DOWN from the main screen to open the Settings menu.

Most rows are either a simple ON/OFF switch, or open a small list of choices. A few open their own sub-page; those are noted below.

Exceptions:

  • While editing a value, long presses don't go back — you need to confirm with ENTER first.
  • Number editors (the flash sync offsets, the lens's custom focal length and the aperture mapping step counts): UP/DOWN change the value by a small step and a long press changes it by a larger one, instead of going back.
  • Text entry (the lens NAME): UP/DOWN change the letter under the cursor, a long UP/DOWN moves the cursor along the name, and a long ENTER clears the whole name (after asking you to confirm).

SELF TIMER

How long the countdown runs before the shutter fires, once you press RELEASE: OFF, 2, 4, 10, 30 or 60 seconds. See Using the self-timer.

EXPOSURE MODE

How the shutter is timed. Press ENTER to open the list, use UP/DOWN to choose, and press ENTER to confirm.

Mode What it does
NORMAL The shutter fires for the shutter speed on the main screen.
LONG The main screen's top row becomes an hours:minutes:seconds duration you set, for exposures longer than 30 seconds.
BULB The shutter stays open for as long as you hold RELEASE.
TIME RELEASE opens the shutter, and pressing RELEASE again closes it.

See Exposure modes for how each one works in use.

ISO

Sets the film sensitivity used to calculate the EV readout on the main screen. This doesn't change how the shutter fires — it's purely there so the exposure value shown is correct for the film you've loaded.

LENS

Opens the Lens sub-menu — selecting, naming, and calibrating the aperture range of your lens. See Setting up a lens for the full walkthrough.

FLASH SYNC

Opens the Flash Sync sub-menu, for firing a flash connected to the Controller's 3.5mm flash sync jack. See Using a flash for how it works in practice.

The FLASH SYNC page.
The FLASH SYNC page.
Setting What it does Options Default
1ST CURTAIN Fire the flash as the shutter opens, at the start of the exposure OFF / ON OFF
2ND CURTAIN Fire the flash as the shutter is about to close, at the end of the exposure OFF / ON OFF
1ST OFFSET Delays the first-curtain flash by this many milliseconds after the shutter starts opening 0 to 255 ms 0
2ND OFFSET Fires the second-curtain flash this many milliseconds earlier than its normal time, just before the shutter closes 0 to -2000 ms 0

Both curtains can be on at once, in which case the flash fires twice. Note that many flashes need a moment to recover between firings, so at fast shutter speeds, where the two pulses are only a few milliseconds apart, a lot of flashes won't be able to fire a second time and will most likely only fire on the first curtain.
Adjusting the offsets with UP/DOWN changes the value by 1 ms and a long press changes it by 10 ms.

Whatever offsets you enter, the flash only ever fires while the shutter is open. If an offset would put the flash before the shutter opens or after it closes, the flash fires at the nearest point inside the exposure instead.

When a curtain is switched on, the fastest shutter speed you can choose is limited to the fastest one the shutter can reliably sync at: currently 1/125 for first curtain and 1/50 for second curtain. With both on, the slower of the two limits applies, and switching a curtain on moves your shutter speed down to that limit if it was faster.

SOUND

Opens the Sound sub-menu:

Setting What it does Default
VOLUME LOW / MEDIUM / HIGH HIGH
UI Beeps for everyday button presses ON
ERROR Beeps/tones for warnings and errors ON
TIMER Beeps during the self-timer countdown ON
TUNE The startup/shutdown tune ON

SAFE SHOT

Switches the extra Arm step on/off before every shot.

By default, the system has an extra safety step called Safe Shot switched on. With Safe Shot on, closing the shutter and aperture isn't enough on its own, you also need to explicitly Arm the system.

With Safe Shot switched off, the system fires any time the shutter and aperture are both closed — closing them is enough, no separate arm step needed, so you can take any number of successive shots without rearming.

INFO

A read-only screen showing:

  • The Controller's firmware version
  • Its serial number
  • Current battery voltage
  • The I-O Shutter's firmware version (SFW) and serial number (SSN), shown only while an I-O Shutter is connected Handy to have to hand if you ever need to contact support.

AUTOSAVE

Off by default. When switched on, the system remembers your current shutter speed, aperture and exposure mode, and starts up with those same values next time you turn it on. (The LONG exposure duration is always remembered.) When switched off, the system always starts up with its factory default values, and any changes you make during a session are forgotten once it's powered off.

POWER

The POWER page.
The POWER page.

Opens the Power sub-menu:

Setting What it does Options Default
SCREEN OFF How long with no button presses before the screen blanks to save power Never / 1 / 5 / 10 / 30 min / 1 hour 5 min
SCR OFF EXP Whether the screen is allowed to blank itself during a long exposure NO (stay lit for the whole exposure) / YES (blank as normal) / ALWAYS (force it off the instant the shot fires) YES
SLEEP How long with no activity before the system goes to sleep to save battery Never / 30 / 60 min / 2 / 5 hours 2 hours
SLEEP MODE What sleeping does. NORMAL sleeps the Controller only; the I-O Shutter stays running. HIBERN also puts the I-O Shutter to sleep for the lowest power use, but it can only be restarted by turning the system off and on again NORMAL / HIBERN NORMAL
BRIGHTNESS Screen brightness LOW / MID / HIGH HIGH

Pressing any button wakes the screen straight away. The system never goes to sleep in the middle of an exposure or while its self-timer is counting down.

When the system wakes from sleep it shows a "Woke from sleep" message; press any button to dismiss it (pressing RELEASE dismisses it and acts as normal). If it was in HIBERN mode it instead shows "Woke from hibernation - please power cycle now", and the I-O Shutter won't work again until you turn the system off and back on.

Firing with the screen off: the RELEASE button doesn't need a separate "wake" press. If the shutter is armed and ready to fire, pressing RELEASE while the screen is off fires the shot straight away and wakes the screen at the same time. The exception is if SCR OFF EXP is set to ALWAYS: the shot still fires immediately, but the screen stays off. (If a self-timer is set, RELEASE starts the countdown instead, as normal. If the shutter isn't ready to fire, you get the usual warning tone and nothing fires.)

UPDATE

Opens the Update sub-menu, used to update the firmware on the Controller or the I-O Shutter. See Updating the firmware before using this.

HELP

A simplified version of this guide.

Setting Up a Lens

The I-O Shutter can remember up to 10 different lenses, each with its own name, focal length and aperture calibration. If you only ever use one lens, you likely won't need to touch most of this — it's here for when you calibrate a new lens for the first time, or switch between several.

The LENS page.
The LENS page.

Open LENS from the Settings menu.

SELECT LENS

Choose which of the 10 saved lens slots is currently active. UP/DOWN browses the saved lenses by name, ENTER switches to the one shown.

NAME

Editing a lens NAME.
Editing a lens NAME.

Give the active lens a name (up to 14 characters), e.g. 150mm f5.6. This uses the Controller's on-screen text entry:

  • UP/DOWN — cycle the character at the cursor
  • Press and hold UP/DOWN — move the cursor
  • ENTER — confirm and save the name
  • Press and hold ENTER — clear the whole name (asks you to confirm first)

FOCAL LENGTH

Sets the lens's focal length, mostly for your own reference. Pick from a list of common large-format focal lengths (65mm–600mm), or choose CUSTOM to dial in any value in 1mm steps.

RESET

Resets the active lens slot back to one of Intrepid's factory presets — useful if a lens matches a lens Intrepid already has calibration data for, or to start over from a known-good baseline. Choose a preset from the list, confirm, and its name, focal length and full aperture calibration overwrite whatever was in that slot.

Current factory presets: Intrepid 150, Rodenstock Geronar, Fujinon SW, Rodenstock Grandagon N.

If your lens is on this list, this is all you need — pick its preset and you're done. We're expanding the preset list over time so that nearly everyone can set up their lens this way, without ever needing Aperture Mapping below.

APERTURE MAPPING (Advanced)

Note: Most users won't need this. Aperture Mapping is for lenses that don't have a factory preset (see RESET above). It takes some time, and doing it accurately needs extra equipment. If a preset exists for your lens, use that instead.

Aperture Mapping tells the I-O Shutter which motor position (steps) corresponds to each f-stop on your specific lens. It's a two-page process.

The Controls

Page 1 — Fstop Min/Max: set the widest (MIN) and smallest (MAX) f-stop your lens supports, then choose OK to move on. This defines the range you'll calibrate across.

Page 2 — Aperture Map:

  • FSTOP — pick an f-stop within your min/max range to calibrate.
  • STEPS — the I-O Shutter drives the aperture to the position currently stored for that f-stop, live, so you can see it move. Adjust with UP/DOWN (press and hold for bigger jumps), then ENTER to set that point. Every time you confirm, the aperture re-homes and moves to the new position so you can check it.
  • Repeat FSTOP → STEPS for each point you want to calibrate — you can revisit any point, in any order, before saving.
  • CLEAR ALL — wipes every calibrated point for this lens, if you want to start over. Asks for confirmation first, since it can't be undone.
  • OK — saves everything and returns to the Lens menu. Nothing is permanently saved until you press this.

To leave without saving: press and hold UP or DOWN on either page. Any points you set since the last OK are discarded.

You only need to calibrate the full stops (e.g. f5.6, f8, f11, f16…). The I-O Shutter automatically fills in the third-stops and any other gaps between the points you calibrate.

Step 1 — the Widest Aperture

This step needs no special equipment.

  1. Mount the lens on the camera, and put a diffused light source in place of the ground glass, so light shines out through the lens towards you.
  2. On page 2, choose FSTOP and select the widest f-stop (the same value as MIN on page 1).
  3. Open STEPS and, while looking into the front of the lens, step through the values until you see the aperture blades just start to appear at the edge of the opening.
  4. Go back about 5 steps, or until the blades just disappear again, then press ENTER.

The widest aperture is now set so the blades sit just outside the light path.

Step 2 — the Remaining Full Stops

This is the harder part, and most users won't have the equipment for it. The most accessible method is to use a digital camera as a light meter:

Setup
  1. Mount a digital camera — with as large a sensor as possible — to the back of the 4x5 camera, using a suitable adapter/mounting plate.
  2. Set up a diffused, stable, constant light source directly in front of the lens.
  3. On the digital camera, only ever use full-stop shutter speeds (e.g. 1/1000, 1/500, 1/250, 1/125, 1/60…) — no third-stop speeds.
  4. With the lens at its widest aperture (calibrated in Step 1), adjust the digital camera's ISO, shutter speed and the focus distance until its light meter reads a perfect exposure (0). Use the focus distance for the final fine-tuning.
Calibrating Each Stop
  1. Choose FSTOP and select the next full stop down (e.g. from f5.6 to f8).
  2. Set the digital camera's shutter speed one stop slower (e.g. 1/250 → 1/125).
  3. Open STEPS and adjust until the digital camera's meter reads 0 again, then press ENTER.
  4. Repeat for each full stop down to the smallest aperture — each time, slow the digital camera's shutter speed by exactly one stop and bring the meter back to 0.

Because the shutter speed changes by exactly one stop each time, bringing the meter back to 0 means the aperture has closed down by exactly one stop.

When every full stop is done, press OK to save.

Updating the Firmware

The Controller and the I-O Shutter each run their own firmware, and are updated separately. You won't need to do this often — only when Intrepid releases an update.

The latest firmware for both units is always here:

Downloads

Latest Firmware

Each unit is updated on its own. Check what yours is running under Settings → INFO.

Firmware downloads will appear here.

How to update

Both updates work the same underlying way: the device restarts into a special mode where it appears on your computer as a small removable drive, and you copy the new firmware file onto it.

Updating the Controller

to your computerSHU is the update port, not CHR
Updates go through SHU. Connect it to your computer with a USB-C cable.
Settings → UPDATE.
Settings → UPDATE.
Updating the Controller: connect it to your computer.
Updating the Controller: connect it to your computer.
  1. Connect the Controller to your computer via its SHU port, using a USB-C cable.
  2. On the Controller, open Settings → UPDATE → CONTROLLER.
  3. The screen asks you to disconnect the I-O Shutter and connect the Controller to a computer. Once it's connected, press any button to continue.
  4. The Controller restarts into update mode and appears on your computer as a removable drive.
  5. Drag the firmware file you downloaded onto that drive.
  6. The Controller copies the file, then restarts automatically running the new firmware — no need to eject the drive manually first.

Updating the I-O Shutter

  1. With the I-O Shutter connected to the Controller as normal, open Settings → UPDATE → SHUTTER.
    • If nothing's connected, the screen will ask you to connect an I-O Shutter first.
  2. The Controller arms the I-O Shutter to enter update mode next time it's connected to a computer.
  3. Disconnect the I-O Shutter from the Controller, then connect it directly to your computer via USB.
  4. It appears on your computer as a removable drive — drag the firmware file onto it, the same as above.
  5. Once it's finished copying, reconnect the I-O Shutter to the Controller as normal.

While an Update Is Copying

The screen shows an "Updating..." message.

Caution: Don't switch off until your computer shows the transfer has finished. The Controller restarts on its own.

If you haven't started copying an update file across yet, it's of course safe to unplug or power off — nothing has been changed at that point.

Troubleshooting

On-screen Messages

Shown when the I-O Shutter loses its connection.
Shown when the I-O Shutter loses its connection.

Message What it means What to do
Shutter connected The I-O Shutter has just connected to the Controller. Nothing — informational only, disappears on its own.
Shutter disconnected / Press any button The I-O Shutter's connection to the Controller has been lost (cable unplugged, I-O Shutter powered down, etc.). Stays on screen until dismissed, since it doesn't clear itself. Check the cable/connection, then press any button to dismiss. Reconnecting the I-O Shutter also dismisses it automatically.
Connect a shutter You tried to update the I-O Shutter's firmware, but none is currently connected. Connect the I-O Shutter, then try again.
Low battery The Controller's battery is getting low. Charge via the CHR port when convenient. Reappears periodically until charged.
No battery detected / Please insert battery The Controller is plugged in via CHR but can't detect its battery. The system needs its battery to work correctly. Switch off, unplug the charge cable, and check the battery is fitted. If it persists with the battery in place, see Warranty and support.
Charging paused / Check temp & charger Charging has stopped because of a problem the charger can recover from: the battery is too hot or too cold, the charge supply's voltage is too high, the charger has overheated, or there's a short. Shown a couple of seconds after the problem starts. It clears as soon as the problem goes. Move the system somewhere cooler or warmer, or try a different cable or USB power source. Charging carries on by itself once the cause goes away. Press any button to hide the message.
Charger fault / Unplug CHR to reset The charger has stopped because of a more serious problem (for example the charge has taken too long, or too much current was drawn from the battery), and it stays stopped until it's reset. Unplug the CHR cable and plug it back in. If it keeps happening, see Warranty and support.
Exposure in progress / Hold RELEASE to cancel A shot is currently running (typically a slow or long exposure). Wait for it to finish, or press and hold RELEASE to cancel it. In BULB and TIME modes a timer counts up instead: let go of RELEASE (BULB) or press it again (TIME) to close the shutter.
Sensor calibrated The aperture position sensor has just been recalibrated (see below). Nothing — shows the result briefly, then clears.

Confirmation Prompts

A few actions replace or clear settings you've made, so the system checks with you first — e.g. resetting a lens to a factory preset, or clearing calibration/text you've entered. These always show what ENTER and every other button will do, so read the on-screen text before pressing anything.

Battery Icon Meanings

Icon shows Meaning
Battery bars Remaining charge, discharging normally
Battery with lightning bolt Plugged in via CHR and charging
Empty battery + warning Very low — charge soon
Battery with ? A charging problem has been detected. See the Charging paused and Charger fault messages above.
Flashing battery with ? + No battery detected message No battery detected while plugged in via CHR

Advanced: Recalibrating the Aperture Sensor

If the aperture doesn't seem to be finding its zero position correctly, you can trigger a fresh sensor calibration: hold the ENTER button down while switching the system on, and keep it held until the I-O Shutter connects. You'll see a "Sensor calibrated" result once it's done.

Advanced: Factory Reset

Holding all four buttons down while switching the system on starts a factory reset. It resets either the Controller or the I-O Shutter, never both at once — which one depends on whether an I-O Shutter happens to be connected at that moment:

  • I-O Shutter connected: only the I-O Shutter is reset — the Controller's own settings are left untouched. Once you release the four buttons, press:
  • RELEASE — full reset: wipes the I-O Shutter's settings and all lens calibration data.
  • ENTER — settings-only reset: resets the I-O Shutter's settings but keeps lens calibration data.
  • Any other button — cancels, resuming normal startup with nothing changed.
  • No I-O Shutter connected: a prompt instead confirms resetting the Controller itself.
  • ENTER confirms; any other button cancels, resuming normal startup with nothing changed.

    If you want to reset both units, do this twice — once with the I-O Shutter connected, once with it disconnected.

    Warning: This can't be undone. Only do this if you're specifically troubleshooting a problem and have been advised to, e.g. by support — everyday problems are almost always solvable without it.

    Once a reset actually runs, the screen shows "Factory reset complete" and the Controller stays halted — switch it off and on again to resume normal use.

    Care and Specifications

    Caring for Your Controller and I-O Shutter

    Shutter and Aperture Blades

    Caution: Never touch the shutter or aperture blades. They are delicate and easily damaged, dust or contaminants such as oils from your fingers can affect how smoothly they operate.

    If there's dust on the blades, or anywhere between the front and rear element threads, only use a soft rubber air blower designed for gently cleaning dust from camera equipment. Don't be tempted to use compressed air — it could damage the shutter.

    Storage

    It doesn't matter what position the shutter and aperture are left in when the system isn't in use. However, if you're storing the I-O Shutter without a lens attached, we recommend leaving both the shutter and aperture open first (see The main screen). This keeps the blades out of the way so they can't be accidentally damaged and helps protect them from dust and other contaminants.

    Specifications

    Dimensions (W x H x D) Weight
    I-O Shutter 74 x 69 x 23 mm 90 g
    Controller 53 x 128 x 29 mm 130 g

    Battery:

    • Charge time: Approximately 1 hour 50 minutes from a low battery to fully charged.
    • Typical battery life: Up to 8 hours powered on with screen saver active, 20 hours in normal sleep mode.
    • Hibernation battery life: over 1 week.
    • Recommended charger: USB charger with an output of 500mA or more.
    • Extreme use: Over 6,000 exposures per charge are possible (but impractical).

    Format compatibility: Copal 0 compatible, built primarily for 4x5 large format cameras. The I-O Shutter can also be used on 5x7 and 8x10 with a larger lens board, though not many Copal 0 lenses that covers 4x5 will produce a large enough image circle for those bigger formats — check your specific lens.

    Flash sync: the Controller's 3.5mm flash sync jack has been tested with flash trigger voltages of up to 200V. The component used is theoretically rated for higher voltages, but we can't guarantee it with flashes we haven't tested. If you're using a vintage flash with a trigger voltage over 200V, we recommend connecting a modern master flash to the Controller instead, and firing the larger flash from it via an optical slave receiver.

    Warranty and Support

    Warranty

    Your Controller and I-O Shutter come with a 1-year warranty. If you break something within that year, we'll repair it for you at cost.

    Getting in Touch

    Get in touch through our contact page.

    Before Contacting Support

    Having the following ready will speed things up:

    • Firmware version and serial number for the Controller (and the I-O Shutter, if connected), from Settings → INFO on the Controller.
    • Whether the I-O Shutter was connected when the problem occurred.
    • What you were trying to do, and what happened instead — a photo/video of the screen helps.